How To Make A Queen Size Pallet Headboard

Dorsum with another super simple pallet project! This one is from our talented friend at "Homesteadonomics".

How to build a pallet headboard. This 1 is very easy depending on your skill level and bachelor tools. Yous should exist able to do this in an 60 minutes or two.

A wood pallet headboard adds a very warm and rustic touch to any chamber. The cool matter is, yous can add different blazon of stains and paints to requite a more modern look. Or, if you similar the rustic-country await, don't add anything.

Click hither for tips on how to find free pallets, this is a bully option because you can use a recycled pallet!

On most pallet wood projects you shouldn't accept to buy supplementary woods. The whole point of a pallet project is that it's gratis and easy.

Even so, considering your wood headboard will need to bridge the width of your bed, you will about likely have to purchase two 8ft 2×3's for your frame. It's not very probable you'll find a pallet that large.

Ok here nosotros go!

How to Make a Pallet Headboard: Table of contents

ane. Disassemble Your Pallets, Wash, and Cutting The Pieces For The Frame
2. Assemble Frame
3. Secure The Frame
4. Attach Slats to Front of Frame
5. Assemble and Attach Corner Pieces To Cover The Edges
half dozen. Top it Off
7. Add Linseed Oil or Stain On Cutting Edges
eight. Sand and Sand Some More

ane. Disassemble Your Pallets, Wash, and Cut The Pieces For The Frame

For this pallet project you will probably need 2-4 pallets. Direct later dismantling, I recommend washing down the forest since the wood will be used equally bedroom decor as a rustic headboard.

Scout this video for quick and easy dismantling tips.

Your DIY headboard frame will accept to be attached to the bed frame, so ensure you get practiced measurements.

2. Gather Frame

This part is pretty piece of cake assuming you have accurate measurements. Use the side pieces of your pallet for the side of the pallet woods headboard.

The 2×three's you purchased will span the width of your frame.

Side by side, use a few of the ii×4 pieces of your pallet betwixt the 2×3's equally structural support.

iii. Secure The Frame

Utilise a nail gun (if you have 1 it makes it much easier) and hit every connection 2-iii times. And then, pre-drill holes and add screws to every frame connectedness.

Don't accept a nail gun? I recommend this one from Dewalt.
DEWALT DWFP12231 Pneumatic xviii-Gauge ii-Inch Brad Nailer Kit

Do not skip this footstep.

The nail gun connections are only to concord it in identify while you add screws, and do non provide very much support.

4. Attach Slats to Front end of Frame

The hardest part of this is cutting your pieces in alternate patterns while maintaining authentic lengths to bridge the wooden headboard. Once that is finished, just attach the slats using your nail gun (or hammer and nails if you lot prefer the long road).

Alternating patterns of the slats is important for the rustic look. Information technology should be easy to attain because pallets are generally a "hodge podge" of types and quality.

5. Assemble and Attach Corner Pieces To Comprehend The Edges

This is a step y'all tin can skip if y'all prefer the edges exposed. If you like the corner pieces, just measure the height of your headboard, cutting four pieces the aforementioned length, and spiral together.

Now adhere to the headboard.

6. Top it Off

Cutting a slice or two that is wide enough to comprehend the top of the headboard and attach. You tin can make the top piece the same width or a few inches longer on each side…whatsoever you like.

7. Add together Linseed Oil or Stain On Cut Edges

Basically, your cut edges will look similar fresh forest, while the balance of the wood will look aged (because it probably is). Calculation linseed oil or stain to your edges will give them a consistent look with the balance of your piece.

8. Sand and Sand Some More

You're basically done at this bespeak. Sanding downwardly the forest pallet headboard with either a piece of sandpaper or powered sander will remove the burs and difficult edges.

Now, you lot can adhere the headboard to your bed frame and you're washed!

This process is going to depend on your bed frame, just essentially, y'all'll probably demand to drill holes that line upwardly with the holes on your bed frame and attach with appropriately sized nuts and bolts.

Now yous've got a unique DIY pallet wood headboard that you've made with your own two hands, hopefully, in nether a few hours.

[su_note]Need Woodworking Plans? Click hither to go over 16,000 woodworking plans.[/su_note]

Remember, as I stated previously, you can always add stains and pigment to give it a different look than you encounter here. Likewise, you tin become creative with your slat layout on the face up for more than pattern options. Watch the full tutorial here.

Click here to bank check out another cool DIY pallet project.